[{"data":1,"prerenderedAt":429},["ShallowReactive",2],{"blog-bare-pcb-storage-disposition-en":3,"header-nav-en":93},{"title":4,"description":5,"date":6,"lastUpdated":6,"category":7,"image":8,"readingTime":9,"wordCount":10,"timeRequired":11,"htmlContent":12,"tableOfContents":13,"tags":38,"slug":43,"jsonld":44},"Bare PCB Storage: What to Do When a Package Is Damaged","Separate moisture, solderability and physical damage when a bare PCB package is damaged or its storage history is uncertain.","2026-11-12","manufacturing","",9,1652,"PT9M","\u003Cp>A torn package or missing storage record does not automatically mean the boards must be discarded, but it does leave an unanswered question before assembly: \u003Cstrong>which boards were exposed, to what conditions, and can the next process use them?\u003C\u002Fstrong> Identify the affected inventory and hold it for review. Then assess moisture exposure, solderable surfaces and physical damage separately using the supplier&#39;s instructions and the project&#39;s acceptance plan.\u003C\u002Fp>\n\u003Cp>An intact-looking bag does not establish the condition of every board inside it, and a humidity indicator card does not measure moisture inside the laminate. Its present reading alone does not establish the complete exposure history; interpret it using the specific indicator&#39;s instructions. Equally, a successful solderability test answers a surface-wetting question; it does not by itself establish the board&#39;s internal moisture condition. The \u003Ca href=\"\u002Fen\u002Fblog\u002Fenig-vs-hasl-vs-enepig\">surface finish comparison\u003C\u002Fa> explains how the finish affects the original purchasing decision.\u003C\u002Fp>\n\u003Ch2 id=\"start-with-the-actual-package-and-lot\" data-anchor-en=\"start-with-the-actual-package-and-lot\">Start with the actual package and lot\u003C\u002Fh2>\n\u003Cp>Before opening, moving or mixing anything further, preserve the available evidence and follow your site&#39;s handling and quarantine procedure. Record:\u003C\u002Fp>\n\u003Cul>\n\u003Cli>Board part number and revision, finish, supplier, lot or date code, quantities, and original package identification.\u003C\u002Fli>\n\u003Cli>Whether the damage is to the shipping carton, a protective outer wrapper, or the sealed board package itself. A torn carton does not prove the inner barrier is punctured; an intact carton does not prove the inner package is sealed.\u003C\u002Fli>\n\u003Cli>The location and extent of any tear, puncture, loose seal, contamination, impact or wetting. Photograph it before disturbing the contents when practical.\u003C\u002Fli>\n\u003Cli>Packaging label and instructions, indicator type and observed indication, desiccant and seal condition, and when the observation was made. Interpret a card according to its own instructions; record an unreadable or absent card as unknown.\u003C\u002Fli>\n\u003Cli>Receipt, opening and resealing times, available storage and transport conditions, and any periods for which the history is missing.\u003C\u002Fli>\n\u003Cli>The intended next operation, including the assembly thermal process and any surface bonding or contact requirements.\u003C\u002Fli>\n\u003C\u002Ful>\n\u003Cp>Keep identification with the boards and avoid touching solderable or contact areas. If you cannot determine which units were affected, do not assume the exposed quantity is zero. Ask quality to define the review boundary using the available \u003Ca href=\"\u002Fen\u002Fblog\u002Fpcb-traceability-lot-control\">PCB traceability and lot records\u003C\u002Fa>.\u003C\u002Fp>\n\u003Ch2 id=\"three-questions-need-three-kinds-of-evidence\" data-anchor-en=\"three-questions-need-three-kinds-of-evidence\">Three questions need three kinds of evidence\u003C\u002Fh2>\n\u003Ctable>\n\u003Cthead>\n\u003Ctr>\n\u003Cth>Question\u003C\u002Fth>\n\u003Cth>Useful evidence\u003C\u002Fth>\n\u003Cth>What it cannot decide alone\u003C\u002Fth>\n\u003C\u002Ftr>\n\u003C\u002Fthead>\n\u003Ctbody>\u003Ctr>\n\u003Ctd>Could the boards have absorbed unacceptable moisture before soldering?\u003C\u002Ftd>\n\u003Ctd>Package condition, indicator instructions and reading, exposure and environment history, construction, planned thermal process, supplier guidance and any agreed moisture assessment.\u003C\u002Ftd>\n\u003Ctd>A humidity card reports its response to surrounding humidity, not the moisture content of each board.\u003C\u002Ftd>\n\u003C\u002Ftr>\n\u003Ctr>\n\u003Ctd>Are the required surfaces still suitable for the next joining operation?\u003C\u002Ftd>\n\u003Ctd>Finish and age, handling and contamination history, intended soldering or bonding operation, and a representative test plan where required.\u003C\u002Ftd>\n\u003Ctd>A visual appearance or calendar date alone does not establish solderability; a solderability result does not establish bondability or internal moisture condition.\u003C\u002Ftd>\n\u003C\u002Ftr>\n\u003Ctr>\n\u003Ctd>Is there physical damage or contamination?\u003C\u002Ftd>\n\u003Ctd>Packaging condition, handling history and inspection of relevant features against the agreed criteria.\u003C\u002Ftd>\n\u003Ctd>A visual inspection does not establish all internal damage, moisture condition or future performance.\u003C\u002Ftd>\n\u003C\u002Ftr>\n\u003C\u002Ftbody>\u003C\u002Ftable>\n\u003Cp>The \u003Ca href=\"\u002Fen\u002Fblog\u002Fsolderability-testing\">solderability testing guide\u003C\u002Fa> discusses how to select test evidence. Agree the sample, surfaces, test method and acceptance criteria with the responsible quality team. A result on one sample should not be treated as evidence for a different finish, package or lot without an agreed basis.\u003C\u002Fp>\n\u003Ch2 id=\"example-one-delivery-two-different-histories\" data-anchor-en=\"example-one-delivery-two-different-histories\">Example: one delivery, two different histories\u003C\u002Fh2>\n\u003Cp>In this hypothetical decision exercise, a delivery contains two separately identified sealed packages of the same board revision. At receiving, the carton is crushed. Package A has a visible puncture; package B looks intact. The delivery records do not show when the impact occurred.\u003C\u002Fp>\n\u003Col>\n\u003Cli>\u003Cstrong>Separate and identify both packages.\u003C\u002Fstrong> Record the package IDs, quantities, labels and visible condition. Do not mix their boards simply because the part numbers match.\u003C\u002Fli>\n\u003Cli>\u003Cstrong>Hold A for disposition.\u003C\u002Fstrong> Its barrier has been breached, but the exposure duration and environment are unknown. Record the indicator reading if the package includes one and its instructions permit interpretation. Do not infer a board moisture measurement from that reading.\u003C\u002Fli>\n\u003Cli>\u003Cstrong>Review B on its own evidence.\u003C\u002Fstrong> Its appearance is useful information, not a complete test of barrier integrity or contents. Compare the shipping event, seal condition, label and available history with the receiving criteria. Quality decides whether B may follow the normal receipt process or also needs review.\u003C\u002Fli>\n\u003Cli>\u003Cstrong>Ask the fabricator and assembler for the missing facts.\u003C\u002Fstrong> Confirm the actual finish, construction, packaging instructions and agreed handling requirements. The assembler supplies the next thermal process and any joining constraints. Record unknowns explicitly.\u003C\u002Fli>\n\u003Cli>\u003Cstrong>Agree a documented outcome for each package.\u003C\u002Fstrong> Depending on the project requirements and evidence, quality may release it, request further evaluation or an approved recovery process, or reject it. Record the authority, evidence and quantity covered by the decision.\u003C\u002Fli>\n\u003C\u002Fol>\n\u003Cp>The key is the separation of histories: a decision about A does not automatically release B, and a decision about B does not repair A&#39;s missing exposure record. If the two packages cannot be traced reliably, agree a conservative common review scope with the product owner.\u003C\u002Fp>\n\u003Ch2 id=\"should-the-boards-be-baked\" data-anchor-en=\"should-the-boards-be-baked\">Should the boards be baked?\u003C\u002Fh2>\n\u003Cp>Baking may reduce absorbed moisture when an appropriate controlled process is specified. It is not a universal remedy for a damaged package, poor solderability, corrosion or physical damage. Heating also has to be compatible with the actual board construction and finish and the operations that follow. For an investigation of existing blistering or separation, see \u003Ca href=\"\u002Fen\u002Fblog\u002Fpcb-delamination-blistering\">PCB delamination and blistering\u003C\u002Fa>.\u003C\u002Fp>\n\u003Cp>Before any recovery cycle, obtain the fabricator&#39;s applicable instructions and agree the cycle, equipment, loading, verification, subsequent handling and approval with the assembler and product owner. A component moisture-sensitivity floor-life or bake schedule is not automatically a bare-board schedule. Do not copy a temperature or duration from a generic chart to resolve an unknown package history.\u003C\u002Fp>\n\u003Cp>If a recovery step is performed, keep a record linked to the affected quantity. Confirm whether additional inspection or solderability evaluation is needed after the process and how long the boards may remain exposed before the next operation. These are project decisions, not assumptions made from a clean-looking surface.\u003C\u002Fp>\n\u003Ch2 id=\"what-does-pcb-shelf-life-mean\" data-anchor-en=\"what-does-pcb-shelf-life-mean\">What does PCB shelf life mean?\u003C\u002Fh2>\n\u003Cp>There is no single useful storage period for every bare PCB. The finish, packaging, environment, handling, required next operation and agreed supplier instructions all matter. An agreed storage limit is a control point for the documented conditions; crossing it triggers the agreed review and any specified disposition, not an automatic assumption that every board has failed. If no disposition is specified, the responsible parties must decide it.\u003C\u002Fp>\n\u003Cp>For planned inventory, agree the storage period and packaging conditions before ordering. Record the start date and package-opening events, and establish who will decide disposition if the history becomes incomplete. Separate the requirements for solderable pads, bonding surfaces and contacts if the product uses more than one of them.\u003C\u002Fp>\n\u003Ch2 id=\"what-should-purchasing-and-quality-ask-the-supplier\" data-anchor-en=\"what-should-purchasing-and-quality-ask-the-supplier\">What should purchasing and quality ask the supplier?\u003C\u002Fh2>\n\u003Cp>Send the board part and revision, finish, quantity and intended use; the affected package IDs; photos; shipment, storage and exposure records; and the next assembly process. Request:\u003C\u002Fp>\n\u003Cul>\n\u003Cli>The packaging and storage conditions agreed for the supplied boards, including how to interpret the actual indicator and label, if present.\u003C\u002Fli>\n\u003Cli>The supplier&#39;s recommendation for the observed breach and unknown history, including any board- and finish-specific recovery restrictions.\u003C\u002Fli>\n\u003Cli>The evidence needed for a release decision: appropriate sampling, inspection or testing, the responsible laboratory or party, acceptance criteria and the scope represented by the result.\u003C\u002Fli>\n\u003Cli>Any approval needed from the product owner before recovery, use, return or rejection, and the identification and traceability to retain afterward.\u003C\u002Fli>\n\u003C\u002Ful>\n\u003Cp>The supplier can advise on its materials and packaging. Confirm in the order who controls the assembly process and who has authority to accept the disposition against the product&#39;s requirements. Do not assume a generic service or report is included.\u003C\u002Fp>\n\u003Cdiv data-component=\"BlogQuickQuoteInline\">\u003C\u002Fdiv>\n\n\u003Cp>Share the board information and handling requirements through the \u003Ca href=\"\u002Fen\u002Fquote\">quote page\u003C\u002Fa> or \u003Ca href=\"\u002Fen\u002Fcontact\">contact APTPCB\u003C\u002Fa>.\u003C\u002Fp>\n\u003C!-- faq:start -->\n\u003Ch2 id=\"frequently-asked-questions\" data-anchor-en=\"frequently-asked-questions\">Frequently asked questions\u003C\u002Fh2>\n\u003Ch3 id=\"does-a-damaged-shipping-carton-mean-all-boards-are-unusable\" data-anchor-en=\"does-a-damaged-shipping-carton-mean-all-boards-are-unusable\">Does a damaged shipping carton mean all boards are unusable?\u003C\u002Fh3>\n\u003Cp>No. Determine whether the inner packaging was damaged, preserve each package&#39;s identity and review its history and applicable receiving criteria. A carton inspection alone cannot establish the condition of all boards.\u003C\u002Fp>\n\u003Ch3 id=\"can-a-humidity-indicator-prove-a-board-is-dry-enough-for-reflow\" data-anchor-en=\"can-a-humidity-indicator-prove-a-board-is-dry-enough-for-reflow\">Can a humidity indicator prove a board is dry enough for reflow?\u003C\u002Fh3>\n\u003Cp>The card indicates humidity according to its design and instructions; it is not a direct measurement of moisture inside each board. Use it with package condition, exposure history and the agreed board-specific assessment.\u003C\u002Fp>\n\u003Ch3 id=\"does-a-passed-solderability-test-release-an-old-board-for-assembly\" data-anchor-en=\"does-a-passed-solderability-test-release-an-old-board-for-assembly\">Does a passed solderability test release an old board for assembly?\u003C\u002Fh3>\n\u003Cp>It can provide evidence about solder wetting under the specified test conditions and sampling plan. It does not alone establish internal moisture condition, physical integrity or suitability for every other joining operation.\u003C\u002Fp>\n\u003Ch3 id=\"are-component-msl-rules-the-same-as-bare-board-storage-rules\" data-anchor-en=\"are-component-msl-rules-the-same-as-bare-board-storage-rules\">Are component MSL rules the same as bare-board storage rules?\u003C\u002Fh3>\n\u003Cp>They address different items. Follow the applicable requirements for classified components and use the board supplier&#39;s instructions and project requirements for bare-board handling and recovery.\u003C\u002Fp>\n\u003Ch3 id=\"which-ipc-document-should-be-specified\" data-anchor-en=\"which-ipc-document-should-be-specified\">Which IPC document should be specified?\u003C\u002Fh3>\n\u003Cp>IPC&#39;s document revision table lists IPC-1601 as superseded by IPC-1602. Identify the exact document and revision required by the purchase order and customer, and resolve any proposed change with the responsible parties. The publicly available IPC-1601A introduction describes its scope; determine applicable requirements from the purchase documents and the relevant controlled specifications.\u003C\u002Fp>\n\u003C!-- faq:end -->\n\n\u003Ch2 id=\"technical-references\" data-anchor-en=\"technical-references\">Technical references\u003C\u002Fh2>\n\u003Cul>\n\u003Cli>IPC, \u003Ca href=\"https:\u002F\u002Fwww.electronics.org\u002FTOC\u002FIPC-1601A.pdf\">\u003Cem>IPC-1601A Printed Board Handling and Storage Guidelines\u003C\u002Fem>\u003C\u002Fa>, public table of contents and introduction, June 2016. The publicly accessible excerpt describes the scope and humidity-indicator terminology; it is not the full controlled document.\u003C\u002Fli>\n\u003Cli>IPC, \u003Ca href=\"https:\u002F\u002Fwww.electronics.org\u002Fipc-document-revision-table\">\u003Cem>Document Revision Table\u003C\u002Fem>\u003C\u002Fa>, accessed November 15, 2026, for the listed relationship between IPC-1601 and IPC-1602. Check the document status and order requirements at the time of use.\u003C\u002Fli>\n\u003C\u002Ful>\n\n\u003Csection class=\"related-links\" aria-label=\"Related\">\u003Ch3>Related links\u003C\u002Fh3>\u003Cul>\u003Cli>\u003Ca href=\"\u002Fen\u002Fblog\u002Fenig-vs-hasl-vs-enepig\">surface finish comparison\u003C\u002Fa>\u003C\u002Fli>\u003Cli>\u003Ca href=\"\u002Fen\u002Fblog\u002Fpcb-traceability-lot-control\">PCB traceability and lot records\u003C\u002Fa>\u003C\u002Fli>\u003Cli>\u003Ca href=\"\u002Fen\u002Fblog\u002Fsolderability-testing\">solderability testing guide\u003C\u002Fa>\u003C\u002Fli>\u003Cli>\u003Ca href=\"\u002Fen\u002Fblog\u002Fpcb-delamination-blistering\">PCB delamination and blistering\u003C\u002Fa>\u003C\u002Fli>\u003Cli>\u003Ca href=\"\u002Fen\u002Fquote\">quote page\u003C\u002Fa>\u003C\u002Fli>\u003Cli>\u003Ca href=\"\u002Fen\u002Fcontact\">contact APTPCB\u003C\u002Fa>\u003C\u002Fli>\u003C\u002Ful>\u003C\u002Fsection>",[14,17,20,23,26,29,32,35],{"id":15,"text":16},"start-with-the-actual-package-and-lot","Start with the actual package and lot",{"id":18,"text":19},"three-questions-need-three-kinds-of-evidence","Three questions need three kinds of evidence",{"id":21,"text":22},"example-one-delivery-two-different-histories","Example: one delivery, two different histories",{"id":24,"text":25},"should-the-boards-be-baked","Should the boards be baked?",{"id":27,"text":28},"what-does-pcb-shelf-life-mean","What does PCB shelf life mean?",{"id":30,"text":31},"what-should-purchasing-and-quality-ask-the-supplier","What should purchasing and quality ask the supplier?",{"id":33,"text":34},"frequently-asked-questions","Frequently asked questions",{"id":36,"text":37},"technical-references","Technical references",[39,40,41,42],"PCB storage","bare board handling","PCB shelf life","PCB solderability","bare-pcb-storage-disposition",{"blog":45,"breadcrumb":54,"faq":68},{"@context":46,"@type":47,"headline":4,"description":5,"url":48,"datePublished":6,"dateModified":6,"timeRequired":11,"keywords":49,"articleSection":7,"author":50,"publisher":53},"https:\u002F\u002Fschema.org","BlogPosting","https:\u002F\u002Faptpcb.com\u002Fen\u002Fblog\u002Fbare-pcb-storage-disposition","PCB storage, bare board handling, PCB shelf life, PCB solderability",{"@type":51,"name":52},"Organization","APTPCB",{"@type":51,"name":52},{"@context":46,"@type":55,"itemListElement":56},"BreadcrumbList",[57,62,66],{"@type":58,"position":59,"name":60,"item":61},"ListItem",1,"Home","https:\u002F\u002Faptpcb.com\u002F",{"@type":58,"position":63,"name":64,"item":65},2,"Blog","https:\u002F\u002Faptpcb.com\u002Fen\u002Fblog",{"@type":58,"position":67,"name":43,"item":48},3,{"@context":46,"@type":69,"mainEntity":70},"FAQPage",[71,77,81,85,89],{"@type":72,"name":73,"acceptedAnswer":74},"Question","Does a damaged shipping carton mean all boards are unusable?",{"@type":75,"text":76},"Answer","No. Determine whether the inner packaging was damaged, preserve each package's identity and review its history and applicable receiving criteria. A carton inspection alone cannot establish the condition of all boards.",{"@type":72,"name":78,"acceptedAnswer":79},"Can a humidity indicator prove a board is dry enough for reflow?",{"@type":75,"text":80},"The card indicates humidity according to its design and instructions; it is not a direct measurement of moisture inside each board. Use it with package condition, exposure history and the agreed board-specific assessment.",{"@type":72,"name":82,"acceptedAnswer":83},"Does a passed solderability test release an old board for assembly?",{"@type":75,"text":84},"It can provide evidence about solder wetting under the specified test conditions and sampling plan. It does not alone establish internal moisture condition, physical integrity or suitability for every other joining operation.",{"@type":72,"name":86,"acceptedAnswer":87},"Are component MSL rules the same as bare-board storage rules?",{"@type":75,"text":88},"They address different items. Follow the applicable requirements for classified components and use the board supplier's instructions and project requirements for bare-board handling and recovery.",{"@type":72,"name":90,"acceptedAnswer":91},"Which IPC document should be specified?",{"@type":75,"text":92},"IPC's document revision table lists IPC-1601 as superseded by IPC-1602. Identify the exact document and revision required by the purchase order and customer, and resolve any proposed change with the responsible parties. The publicly available IPC-1601A introduction describes its scope; determine applicable requirements from the purchase documents and the relevant controlled specifications.",{"pcbManufacturingColumns":94,"capabilityColumns":222,"resourceColumns":258,"pcbaColumns":302},[95,143,172,201],{"heading":96,"links":97},"PCB Product Families",[98,101,104,107,110,113,116,119,122,125,128,131,134,137,140],{"label":99,"path":100},"FR-4 PCB","\u002Fpcb\u002Ffr4-pcb",{"label":102,"path":103},"High-Speed PCB","\u002Fpcb\u002Fhigh-speed-pcb",{"label":105,"path":106},"Multilayer PCB","\u002Fpcb\u002Fmultilayer-pcb",{"label":108,"path":109},"HDI PCB","\u002Fpcb\u002Fhdi-pcb",{"label":111,"path":112},"Flexible PCB","\u002Fpcb\u002Fflex-pcb",{"label":114,"path":115},"Rigid Flex PCB","\u002Fpcb\u002Frigid-flex-pcb",{"label":117,"path":118},"Ceramic PCB","\u002Fpcb\u002Fceramic-pcb",{"label":120,"path":121},"Heavy Copper PCB","\u002Fpcb\u002Fheavy-copper-pcb",{"label":123,"path":124},"High Thermal PCB","\u002Fpcb\u002Fhigh-thermal-pcb",{"label":126,"path":127},"Antenna PCB","\u002Fpcb\u002Fantenna-pcb",{"label":129,"path":130},"High Frequency PCB","\u002Fpcb\u002Fhigh-frequency-pcb",{"label":132,"path":133},"Microwave PCB","\u002Fpcb\u002Fmicrowave-pcb",{"label":135,"path":136},"Metal Core PCB","\u002Fpcb\u002Fmetal-core-pcb",{"label":138,"path":139},"High-Tg PCB","\u002Fpcb\u002Fhigh-tg-pcb",{"label":141,"path":142},"Backplane PCB","\u002Fpcb\u002Fbackplane-pcb",{"sections":144},[145],{"heading":146,"links":147},"RF & Materials",[148,151,154,157,160,163,166,169],{"label":149,"path":150},"Rogers PCB","\u002Fmaterials\u002Frf-rogers",{"label":152,"path":153},"Taconic PCB","\u002Fmaterials\u002Ftaconic-pcb",{"label":155,"path":156},"Teflon PCB","\u002Fmaterials\u002Fteflon-pcb",{"label":158,"path":159},"Arlon PCB","\u002Fmaterials\u002Farlon-pcb",{"label":161,"path":162},"Megtron PCB","\u002Fmaterials\u002Fmegtron-pcb",{"label":164,"path":165},"ISOLA PCB","\u002Fmaterials\u002Fisola-pcb",{"label":167,"path":168},"Spread Glass FR-4","\u002Fmaterials\u002Fspread-glass-fr4",{"label":170,"path":171},"Impedance Control","\u002Fpcb\u002Fpcb-impedance-control",{"sections":173},[174],{"heading":175,"links":176},"Manufacturing \u002F Stackups",[177,180,183,186,189,192,195,198],{"label":178,"path":179},"Quickturn Prototypes","\u002Fpcb\u002Fquick-turn-pcb",{"label":181,"path":182},"NPI & Small Batch (PCB)","\u002Fpcb\u002Fnpi-small-batch-pcb-manufacturing",{"label":184,"path":185},"High-Volume Production","\u002Fpcb\u002Fmass-production-pcb-manufacturing",{"label":187,"path":188},"High Layer Count PCB","\u002Fpcb\u002Fhigh-layer-count-pcb",{"label":190,"path":191},"PCB Fabrication Process","\u002Fpcb\u002Fpcb-fabrication-process",{"label":193,"path":194},"Advanced PCB Manufacturing","\u002Fpcb\u002Fadvanced-pcb-manufacturing",{"label":196,"path":197},"Special PCB Manufacturing","\u002Fpcb\u002Fspecial-pcb-manufacturing",{"label":199,"path":200},"Multi-Layer Laminated Structure","\u002Fpcb\u002Fmultilayer-pcb-lamination-services",{"heading":202,"links":203},"Specialties & Resources",[204,207,210,213,216,219],{"label":205,"path":206},"PCB Design & Layout Services","\u002Fpcba\u002Fpcb-design-services",{"label":208,"path":209},"PCB Surface Finishes","\u002Fpcb\u002Fpcb-surface-finishes",{"label":211,"path":212},"PCB Drilling & Vias","\u002Fpcb\u002Fpcb-drilling",{"label":214,"path":215},"PCB Stackup","\u002Fpcb\u002Fpcb-stack-up",{"label":217,"path":218},"PCB Profiling","\u002Fpcb\u002Fpcb-profiling",{"label":220,"path":221},"Quality & Inspection","\u002Fpcb\u002Fpcb-quality",[223,228,233,238,243,248,253],{"links":224},[225],{"label":226,"path":227},"Rigid PCB Capability","\u002Fcapabilities\u002Frigid-pcb",{"links":229},[230],{"label":231,"path":232},"Rigid-Flex Capability","\u002Fcapabilities\u002Frigid-flex-pcb",{"links":234},[235],{"label":236,"path":237},"Flex PCB Capability","\u002Fcapabilities\u002Fflex-pcb",{"links":239},[240],{"label":241,"path":242},"HDI PCB Capability","\u002Fcapabilities\u002Fhdi-pcb",{"links":244},[245],{"label":246,"path":247},"Metal PCB Capability","\u002Fcapabilities\u002Fmetal-pcb",{"links":249},[250],{"label":251,"path":252},"Ceramic PCB Capability","\u002Fcapabilities\u002Fceramic-pcb",{"links":254},[255],{"label":256,"path":257},"Heavy Copper PCB Capability","\u002Fcapabilities\u002Fheavy-copper-pcb",[259,270,294],{"heading":260,"links":261},"Downloads",[262,265,268],{"label":263,"path":264},"Materials Datasheet \u002F Processing Notes","\u002Fresources\u002Fdownloads-materials",{"label":266,"path":267},"PCB DFM Guidelines","\u002Fresources\u002Fdfm-guidelines",{"label":199,"path":269},"\u002Fpcb\u002Fmulti-layer-laminated-structure",{"heading":271,"links":272},"Tools",[273,276,279,282,285,288,291],{"label":274,"path":275},"Gerber Viewer","\u002Ftools\u002Fgerber-viewer",{"label":277,"path":278},"PCB Viewer","\u002Ftools\u002Fpcb-viewer",{"label":280,"path":281},"BOM Viewer","\u002Ftools\u002Fbom-viewer",{"label":283,"path":284},"3D Viewer","\u002Ftools\u002F3d-viewer",{"label":286,"path":287},"Circuit Simulator","\u002Ftools\u002Fcircuit-simulator",{"label":289,"path":290},"Impedance Calculator","\u002Ftools\u002Fimpedance-calculator",{"label":292,"path":293},"Trace Width Calculator","\u002Ftools\u002Ftrace-width-calculator",{"heading":295,"links":296},"FAQ & Blog",[297,300],{"label":298,"path":299},"FAQ","\u002Fresources\u002Ffaq",{"label":64,"path":301},"\u002Fblog",[303,333,359,392],{"heading":304,"links":305},"Core Services",[306,309,312,315,318,321,324,327,330],{"label":307,"path":308},"Turnkey PCB Assembly","\u002Fpcba\u002Fturnkey-assembly",{"label":310,"path":311},"NPI & Small Batch PCB Assembly","\u002Fpcba\u002Fnpi-assembly",{"label":313,"path":314},"Mass Production PCB Assembly","\u002Fpcba\u002Fmass-production",{"label":316,"path":317},"Flex & Rigid-Flex PCB Assembly","\u002Fpcba\u002Fflex-rigid-flex",{"label":319,"path":320},"SMT & Through-Hole Assembly","\u002Fpcba\u002Fsmt-tht",{"label":322,"path":323},"BGA PCB Assembly","\u002Fpcba\u002Fbga-qfn-fine-pitch",{"label":325,"path":326},"Components & BOM Management","\u002Fpcba\u002Fcomponents-bom",{"label":328,"path":329},"Box Build Assembly","\u002Fpcba\u002Fbox-build-assembly",{"label":331,"path":332},"PCB Assembly Testing & Quality","\u002Fpcba\u002Ftesting-quality",{"heading":334,"links":335},"Supporting Services",[336,338,341,344,347,350,353,356],{"label":337,"path":206},"PCB Design & Layout",{"label":339,"path":340},"Every Support Touchpoint","\u002Fpcba\u002Fsupport-services",{"label":342,"path":343},"Stencil Lab","\u002Fpcba\u002Fpcb-stencil",{"label":345,"path":346},"Components Sourcing","\u002Fpcba\u002Fcomponent-sourcing",{"label":348,"path":349},"IC Programming","\u002Fpcba\u002Fic-programming",{"label":351,"path":352},"Conformal Coating","\u002Fpcba\u002Fpcb-conformal-coating",{"label":354,"path":355},"Selective Soldering","\u002Fpcba\u002Fpcb-selective-soldering",{"label":357,"path":358},"BGA Reballing","\u002Fpcba\u002Fbga-reballing",{"heading":360,"links":361},"Quality & Testing",[362,365,368,371,374,377,380,383,386,389],{"label":363,"path":364},"Quality Inspection","\u002Fpcba\u002Fquality-system",{"label":366,"path":367},"First Article Inspection (FAI)","\u002Fpcba\u002Ffirst-article-inspection",{"label":369,"path":370},"Solder Paste Inspection (SPI)","\u002Fpcba\u002Fspi-inspection",{"label":372,"path":373},"AOI Optical Inspection","\u002Fpcba\u002Faoi-inspection",{"label":375,"path":376},"X-Ray \u002F CT Inspection","\u002Fpcba\u002Fxray-inspection",{"label":378,"path":379},"ICT In-Circuit Testing","\u002Fpcba\u002Fict-test",{"label":381,"path":382},"Flying Probe Testing","\u002Fpcba\u002Fflying-probe-testing",{"label":384,"path":385},"FCT \u002F Functional Testing","\u002Fpcba\u002Ffct-test",{"label":387,"path":388},"Final Inspection & Packing","\u002Fpcba\u002Ffinal-quality-inspection",{"label":390,"path":391},"Incoming Quality Control","\u002Fpcba\u002Fincoming-quality-control",{"heading":393,"linkClass":394,"links":395},"Industry Applications (Entry)","text-nowrap",[396,399,402,405,408,411,414,417,420,423,426],{"label":397,"path":398},"Server \u002F Data Center","\u002Findustries\u002Fserver-data-center-pcb",{"label":400,"path":401},"Automotive \u002F EV","\u002Findustries\u002Fautomotive-electronics-pcb",{"label":403,"path":404},"Medical","\u002Findustries\u002Fmedical-pcb",{"label":406,"path":407},"Telecom \u002F 5G","\u002Findustries\u002Fcommunication-equipment-pcb",{"label":409,"path":410},"Aerospace & Defense","\u002Findustries\u002Faerospace-defense-pcb",{"label":412,"path":413},"Drone \u002F UAV","\u002Findustries\u002Fdrone-uav-pcb",{"label":415,"path":416},"Industrial Control & Automation","\u002Findustries\u002Findustrial-control-pcb",{"label":418,"path":419},"Power & New Energy","\u002Findustries\u002Fpower-energy-pcb",{"label":421,"path":422},"Robotics & Automation","\u002Findustries\u002Frobotics-pcb",{"label":424,"path":425},"Security \u002F Security Equipment","\u002Findustries\u002Fsecurity-equipment-pcb",{"label":427,"path":428},"PCB Industry Overview →","\u002Fpcb-industry-solutions",1794926050006]