[{"data":1,"prerenderedAt":426},["ShallowReactive",2],{"blog-pcb-laminate-moisture-absorption-en":3,"header-nav-en":90},{"title":4,"description":5,"date":6,"lastUpdated":6,"category":7,"image":8,"readingTime":9,"wordCount":10,"timeRequired":11,"htmlContent":12,"tableOfContents":13,"tags":38,"slug":44,"jsonld":45},"PCB Laminate Moisture Absorption: Reading and Comparing Data Sheets","Compare PCB laminate moisture absorption data and consider storage, reflow and PCB assembly requirements when selecting materials.","2026-11-16","materials","",9,1660,"PT9M","\u003Cp>The moisture absorption percentage on a PCB laminate data sheet describes a \u003Cstrong>material test result under specified conditions\u003C\u002Fstrong>. It is not the current moisture content of a finished board, a shelf-life limit, or a direct measure of how many soldering cycles the board can tolerate. To compare materials, first check what was tested, how it was conditioned and exposed, and how the result was reported.\u003C\u002Fp>\n\u003Cp>This matters when a board may be stored before assembly, exposed to humidity in service, or processed through thermal cycles. A lower reported number can be useful evidence, but the complete construction, packaging, storage history and intended process still need review.\u003C\u002Fp>\n\u003Cp>This article focuses on \u003Cstrong>laminate data and board-material exposure\u003C\u002Fstrong>. For packaged components and their handling history, use the separate component-maker and assembly procedures; component moisture sensitivity levels do not by themselves define a bare-board storage or baking plan. The broader \u003Ca href=\"\u002Fen\u002Fblog\u002Fpcb-material-selection\">PCB material selection guide\u003C\u002Fa> covers trade-offs beyond moisture, while \u003Ca href=\"\u002Fen\u002Fblog\u002Fpcb-delamination-blistering\">PCB delamination and blistering\u003C\u002Fa> addresses how to investigate an observed separation.\u003C\u002Fp>\n\u003Ch2 id=\"what-does-the-percentage-describe\" data-anchor-en=\"what-does-the-percentage-describe\">What does the percentage describe?\u003C\u002Fh2>\n\u003Cp>Moisture absorption data commonly express a mass change relative to a defined specimen mass after a specified exposure. The data sheet and method determine the actual specimen, preparation, exposure and calculation. A number expressed as a percentage is not enough to reconstruct those conditions.\u003C\u002Fp>\n\u003Cp>As a \u003Cstrong>hypothetical arithmetic example\u003C\u002Fstrong>, suppose a test procedure defines a dry reference mass of 2.000 g and a specimen gains 0.003 g under its stated exposure. The increase relative to that reference is 0.003 \u002F 2.000 × 100 = \u003Cstrong>0.15% by mass\u003C\u002Fstrong>. These hypothetical figures illustrate the calculation; they are not a measurement of an installed PCB or an acceptance limit.\u003C\u002Fp>\n\u003Cp>Do not use the percentage as if it applied uniformly to every board in a shipment. A data-sheet specimen and a manufactured board differ in construction, copper coverage, thickness, surface finish, storage and history. The rate and extent of moisture uptake under an actual environment are not established by one data-sheet figure alone.\u003C\u002Fp>\n\u003Ch2 id=\"read-the-test-conditions-before-ranking-materials\" data-anchor-en=\"read-the-test-conditions-before-ranking-materials\">Read the test conditions before ranking materials\u003C\u002Fh2>\n\u003Cp>The following fields make a comparison more useful. Some may not appear on the short product data sheet; request the test report or a clarification if they affect the decision.\u003C\u002Fp>\n\u003Ctable>\n\u003Cthead>\n\u003Ctr>\n\u003Cth>Check\u003C\u002Fth>\n\u003Cth>What to record\u003C\u002Fth>\n\u003Cth>Why it matters\u003C\u002Fth>\n\u003C\u002Ftr>\n\u003C\u002Fthead>\n\u003Ctbody>\u003Ctr>\n\u003Ctd>Material and construction\u003C\u002Ftd>\n\u003Ctd>Supplier, product, laminate or prepreg, specimen thickness and any reported construction\u003C\u002Ftd>\n\u003Ctd>A product-family label alone may not describe the proposed stackup or the specimen.\u003C\u002Ftd>\n\u003C\u002Ftr>\n\u003Ctr>\n\u003Ctd>Exposure\u003C\u002Ftd>\n\u003Ctd>Whether the method uses immersion, humidity or another exposure, including time and temperature\u003C\u002Ftd>\n\u003Ctd>A water-immersion result is not automatically interchangeable with a humid-air storage result.\u003C\u002Ftd>\n\u003C\u002Ftr>\n\u003Ctr>\n\u003Ctd>Conditioning and reference mass\u003C\u002Ftd>\n\u003Ctd>Preparation, conditioning and the baseline used for the reported mass change\u003C\u002Ftd>\n\u003Ctd>Different starting conditions or calculations can make results difficult to compare.\u003C\u002Ftd>\n\u003C\u002Ftr>\n\u003Ctr>\n\u003Ctd>Test method and revision\u003C\u002Ftd>\n\u003Ctd>Method identifier and edition, together with any supplier departures\u003C\u002Ftd>\n\u003Ctd>A method name helps identify the procedure but does not replace the actual test conditions.\u003C\u002Ftd>\n\u003C\u002Ftr>\n\u003Ctr>\n\u003Ctd>Value type\u003C\u002Ftd>\n\u003Ctd>Typical value, specification limit, lot measurement or other stated basis\u003C\u002Ftd>\n\u003Ctd>A typical figure is not automatically a guaranteed maximum for a purchase order.\u003C\u002Ftd>\n\u003C\u002Ftr>\n\u003Ctr>\n\u003Ctd>Intended decision\u003C\u002Ftd>\n\u003Ctd>Storage, assembly exposure, electrical performance in humidity or another concern\u003C\u002Ftd>\n\u003Ctd>The material test must be connected to evidence for the actual board and use.\u003C\u002Ftd>\n\u003C\u002Ftr>\n\u003C\u002Ftbody>\u003C\u002Ftable>\n\u003Cp>If one supplier states only a number and a method while another also reports time, temperature and specimen thickness, the extra information does not mean the products are directly rankable. Ask for the missing conditions and whether the results are intended to be compared.\u003C\u002Fp>\n\u003Ch2 id=\"how-to-read-a-published-data-sheet-example\" data-anchor-en=\"how-to-read-a-published-data-sheet-example\">How to read a published data-sheet example\u003C\u002Fh2>\n\u003Cp>The Rogers RO4000 series data sheet lists typical moisture absorption values of \u003Cstrong>0.06%\u003C\u002Fstrong> for both RO4003C and RO4350B laminates. The table specifies ASTM D570, 48-hour immersion at 50 °C and a 0.060-inch specimen. Its notes say that the table covers RO4000 laminates without added LoPro resin and that typical values represent population averages, not specification limits.\u003C\u002Fp>\n\u003Cp>Before comparing these values with another product, ask for the specimen preparation, calculation, method revision and exposure conditions for both results. Confirm the applicable product and current purchasing specification with each supplier. A result from immersion is not automatically comparable to one from humid-air exposure.\u003C\u002Fp>\n\u003Cp>The reported values do not predict the moisture content of a finished PCB or guarantee survival of a particular assembly process. They are not generic values for all high-frequency laminates.\u003C\u002Fp>\n\u003Ch2 id=\"why-a-material-result-is-only-part-of-the-board-decision\" data-anchor-en=\"why-a-material-result-is-only-part-of-the-board-decision\">Why a material result is only part of the board decision\u003C\u002Fh2>\n\u003Cp>Moisture can matter to a PCB in several ways, depending on the product and exposure. During a rapid thermal process, moisture is one possible contributor to damage at susceptible interfaces. Moisture and humidity may also be relevant to insulation or dielectric behavior for some constructions and environments. The importance, direction and magnitude of those effects must be established for the actual design and test conditions.\u003C\u002Fp>\n\u003Cp>An observed blister or separation is not proof of moisture as the root cause. Process history, bonding, contamination, fabrication defects and thermal exposure may also matter. Preserve the affected board and records, identify the location of the damage and agree on an investigation before assigning cause. Likewise, a low data-sheet absorption value does not alone prove immunity from conductive anodic filament formation; see \u003Ca href=\"\u002Fen\u002Fblog\u002Fpcb-conductive-anodic-filament\">CAF risk in PCBs\u003C\u002Fa> for the separate geometry, material and test questions.\u003C\u002Fp>\n\u003Cp>For high-frequency designs, ask whether electrical property data and models represent the relevant environmental condition. A dry material Dk or Df number should not be treated as a measured wet-board channel result. The \u003Ca href=\"\u002Fen\u002Fblog\u002Fwhat-is-dielectric-constant\">dielectric constant guide\u003C\u002Fa> explains the wider electrical context.\u003C\u002Fp>\n\u003Ch2 id=\"example-a-shipment-waits-before-assembly\" data-anchor-en=\"example-a-shipment-waits-before-assembly\">Example: a shipment waits before assembly\u003C\u002Fh2>\n\u003Cp>Suppose an assembler receives a sealed shipment of multilayer boards for a humid-environment product. Assembly is delayed, and a partial shipment will be opened and used later. The following is a \u003Cstrong>hypothetical planning example\u003C\u002Fstrong>, not an observation of a tested lot.\u003C\u002Fp>\n\u003Col>\n\u003Cli>\u003Cstrong>Identify the actual construction.\u003C\u002Fstrong> Confirm the approved materials, stackup, board revision and lot. A laminate data sheet is useful background, but it does not identify the exposure of the boards in the box.\u003C\u002Fli>\n\u003Cli>\u003Cstrong>Collect the packaging and storage record.\u003C\u002Fstrong> Note shipment date, package condition, opening date, storage conditions and the fabricator&#39;s handling instructions. Preserve records for any separate partial lots.\u003C\u002Fli>\n\u003Cli>\u003Cstrong>Check the intended thermal process.\u003C\u002Fstrong> Ask the assembler about the planned reflow and any later rework, and share the board construction and fabrication guidance. Determine which instructions govern this specific job.\u003C\u002Fli>\n\u003Cli>\u003Cstrong>Resolve missing or abnormal history.\u003C\u002Fstrong> If a seal is damaged or exposure cannot be established, place the affected lot on hold and obtain a documented disposition from the responsible parties. Do not use a data-sheet percentage as a substitute for the missing history. See \u003Ca href=\"\u002Fen\u002Fblog\u002Fbare-pcb-storage-disposition\">bare PCB storage and damaged-package disposition\u003C\u002Fa> for the receiving workflow.\u003C\u002Fli>\n\u003Cli>\u003Cstrong>Agree on evidence for the product.\u003C\u002Fstrong> If humidity is important in service, select representative conditioning and board or assembly tests with the product team. Define acceptance and how the test represents the design&#39;s real exposure.\u003C\u002Fli>\n\u003C\u002Fol>\n\u003Cp>The possible result may be release under the applicable instructions, additional assessment, controlled processing or replacement. The right choice depends on the actual condition and the responsible team&#39;s documented decision. There is no universal time or temperature in a laminate data sheet that can be turned into a safe baking recipe for every bare or assembled board.\u003C\u002Fp>\n\u003Ch2 id=\"what-to-ask-the-fabricator-and-assembler\" data-anchor-en=\"what-to-ask-the-fabricator-and-assembler\">What to ask the fabricator and assembler\u003C\u002Fh2>\n\u003Cp>Provide the proposed stackup and intended assembly and operating environments. Include the expected time between fabrication and assembly, packaging and storage conditions, any known humidity exposure, and the planned thermal processes. Then ask:\u003C\u002Fp>\n\u003Cul>\n\u003Cli>Which laminate and prepreg products and constructions are proposed, and what moisture-test data and revisions apply to them?\u003C\u002Fli>\n\u003Cli>What specimen, conditioning, method, exposure and calculation support the reported figures? Are they typical values or controlled purchasing limits?\u003C\u002Fli>\n\u003Cli>Which packaging, storage, opening and traceability instructions apply to the delivered \u003Cstrong>bare-board lot\u003C\u002Fstrong>?\u003C\u002Fli>\n\u003Cli>If storage history is uncertain, who decides the hold, assessment, processing and release? What records will be supplied?\u003C\u002Fli>\n\u003Cli>Are material substitutions permitted, and what electrical, thermal and reliability evidence is needed before they are approved?\u003C\u002Fli>\n\u003Cli>What representative board or assembly conditioning and testing is appropriate for the product&#39;s service environment?\u003C\u002Fli>\n\u003C\u002Ful>\n\u003Cp>If components are already mounted, involve the assembler and component suppliers before any proposed drying or rework. Components, finishes, assembly materials and carriers can place different limits on a process; instructions for one material or bare-board lot should not be assumed to apply to the populated assembly.\u003C\u002Fp>\n\u003Cdiv data-component=\"BlogQuickQuoteInline\">\u003C\u002Fdiv>\n\n\u003Cp>APTPCB offers PCB fabrication and \u003Ca href=\"\u002Fen\u002Fpcba\u002Fturnkey-assembly\">turnkey PCB assembly\u003C\u002Fa>. To discuss your project, share the requirements and unresolved exposure questions through the \u003Ca href=\"\u002Fen\u002Fquote\">quote page\u003C\u002Fa> or \u003Ca href=\"\u002Fen\u002Fcontact\">contact APTPCB\u003C\u002Fa>. The product team remains responsible for the final environmental requirements and qualification plan.\u003C\u002Fp>\n\u003C!-- faq:start -->\n\u003Ch2 id=\"frequently-asked-questions\" data-anchor-en=\"frequently-asked-questions\">Frequently asked questions\u003C\u002Fh2>\n\u003Ch3 id=\"is-a-lower-moisture-absorption-percentage-always-better\" data-anchor-en=\"is-a-lower-moisture-absorption-percentage-always-better\">Is a lower moisture absorption percentage always better?\u003C\u002Fh3>\n\u003Cp>It may help when the results and test conditions are comparable, but selection also depends on electrical, thermal, mechanical, manufacturing and supply requirements. Ask whether the available figure supports the intended decision.\u003C\u002Fp>\n\u003Ch3 id=\"can-i-use-an-immersion-value-as-the-board39s-moisture-content-after-storage\" data-anchor-en=\"can-i-use-an-immersion-value-as-the-boards-moisture-content-after-storage\">Can I use an immersion value as the board&#39;s moisture content after storage?\u003C\u002Fh3>\n\u003Cp>No. A controlled material test and a board&#39;s actual storage history are different things. Get the board-lot handling information and any appropriate inspection or test evidence.\u003C\u002Fp>\n\u003Ch3 id=\"does-a-sealed-bag-prove-a-board-is-ready-for-assembly\" data-anchor-en=\"does-a-sealed-bag-prove-a-board-is-ready-for-assembly\">Does a sealed bag prove a board is ready for assembly?\u003C\u002Fh3>\n\u003Cp>Not by itself. Confirm the package condition, identification, relevant storage instructions and records, and any applicable time or environmental limits.\u003C\u002Fp>\n\u003Ch3 id=\"can-i-choose-a-baking-cycle-from-the-absorption-percentage\" data-anchor-en=\"can-i-choose-a-baking-cycle-from-the-absorption-percentage\">Can I choose a baking cycle from the absorption percentage?\u003C\u002Fh3>\n\u003Cp>No. Obtain the applicable board, assembly and component instructions and a documented disposition for the actual lot. A single material property is not a complete processing plan.\u003C\u002Fp>\n\u003C!-- faq:end -->\n\n\u003Ch2 id=\"technical-references\" data-anchor-en=\"technical-references\">Technical references\u003C\u002Fh2>\n\u003Cul>\n\u003Cli>Rogers, \u003Ca href=\"https:\u002F\u002Fwww.rogerscorp.com\u002F-\u002Fmedia\u002Fproject\u002Frogerscorp\u002Fdocuments\u002Fadvanced-electronics-solutions\u002Fenglish\u002Fdata-sheets\u002Fro4000-laminates-ro4003c-and-ro4350b---data-sheet.pdf\">RO4000 series data sheet\u003C\u002Fa>, typical values table and notes, retrieved November 15, 2026. Confirm the applicable product and current specification before use.\u003C\u002Fli>\n\u003C\u002Ful>\n\n\u003Csection class=\"related-links\" aria-label=\"Related\">\u003Ch3>Related links\u003C\u002Fh3>\u003Cul>\u003Cli>\u003Ca href=\"\u002Fen\u002Fblog\u002Fpcb-material-selection\">PCB material selection guide\u003C\u002Fa>\u003C\u002Fli>\u003Cli>\u003Ca href=\"\u002Fen\u002Fblog\u002Fpcb-delamination-blistering\">PCB delamination and blistering\u003C\u002Fa>\u003C\u002Fli>\u003Cli>\u003Ca href=\"\u002Fen\u002Fblog\u002Fpcb-conductive-anodic-filament\">CAF risk in PCBs\u003C\u002Fa>\u003C\u002Fli>\u003Cli>\u003Ca href=\"\u002Fen\u002Fblog\u002Fwhat-is-dielectric-constant\">dielectric constant guide\u003C\u002Fa>\u003C\u002Fli>\u003Cli>\u003Ca href=\"\u002Fen\u002Fblog\u002Fbare-pcb-storage-disposition\">bare PCB storage and damaged-package disposition\u003C\u002Fa>\u003C\u002Fli>\u003Cli>\u003Ca href=\"\u002Fen\u002Fpcba\u002Fturnkey-assembly\">turnkey PCB assembly\u003C\u002Fa>\u003C\u002Fli>\u003Cli>\u003Ca href=\"\u002Fen\u002Fquote\">quote page\u003C\u002Fa>\u003C\u002Fli>\u003C\u002Ful>\u003C\u002Fsection>",[14,17,20,23,26,29,32,35],{"id":15,"text":16},"what-does-the-percentage-describe","What does the percentage describe?",{"id":18,"text":19},"read-the-test-conditions-before-ranking-materials","Read the test conditions before ranking materials",{"id":21,"text":22},"how-to-read-a-published-data-sheet-example","How to read a published data-sheet example",{"id":24,"text":25},"why-a-material-result-is-only-part-of-the-board-decision","Why a material result is only part of the board decision",{"id":27,"text":28},"example-a-shipment-waits-before-assembly","Example: a shipment waits before assembly",{"id":30,"text":31},"what-to-ask-the-fabricator-and-assembler","What to ask the fabricator and assembler",{"id":33,"text":34},"frequently-asked-questions","Frequently asked questions",{"id":36,"text":37},"technical-references","Technical references",[39,40,41,42,43],"PCB moisture absorption","PCB laminate","material selection","PCB reliability","PCB assembly","pcb-laminate-moisture-absorption",{"blog":46,"breadcrumb":55,"faq":69},{"@context":47,"@type":48,"headline":4,"description":5,"url":49,"datePublished":6,"dateModified":6,"timeRequired":11,"keywords":50,"articleSection":7,"author":51,"publisher":54},"https:\u002F\u002Fschema.org","BlogPosting","https:\u002F\u002Faptpcb.com\u002Fen\u002Fblog\u002Fpcb-laminate-moisture-absorption","PCB moisture absorption, PCB laminate, material selection, PCB reliability, PCB assembly",{"@type":52,"name":53},"Organization","APTPCB",{"@type":52,"name":53},{"@context":47,"@type":56,"itemListElement":57},"BreadcrumbList",[58,63,67],{"@type":59,"position":60,"name":61,"item":62},"ListItem",1,"Home","https:\u002F\u002Faptpcb.com\u002F",{"@type":59,"position":64,"name":65,"item":66},2,"Blog","https:\u002F\u002Faptpcb.com\u002Fen\u002Fblog",{"@type":59,"position":68,"name":44,"item":49},3,{"@context":47,"@type":70,"mainEntity":71},"FAQPage",[72,78,82,86],{"@type":73,"name":74,"acceptedAnswer":75},"Question","Is a lower moisture absorption percentage always better?",{"@type":76,"text":77},"Answer","It may help when the results and test conditions are comparable, but selection also depends on electrical, thermal, mechanical, manufacturing and supply requirements. Ask whether the available figure supports the intended decision.",{"@type":73,"name":79,"acceptedAnswer":80},"Can I use an immersion value as the board's moisture content after storage?",{"@type":76,"text":81},"No. A controlled material test and a board's actual storage history are different things. Get the board-lot handling information and any appropriate inspection or test evidence.",{"@type":73,"name":83,"acceptedAnswer":84},"Does a sealed bag prove a board is ready for assembly?",{"@type":76,"text":85},"Not by itself. Confirm the package condition, identification, relevant storage instructions and records, and any applicable time or environmental limits.",{"@type":73,"name":87,"acceptedAnswer":88},"Can I choose a baking cycle from the absorption percentage?",{"@type":76,"text":89},"No. Obtain the applicable board, assembly and component instructions and a documented disposition for the actual lot. A single material property is not a complete processing plan.",{"pcbManufacturingColumns":91,"capabilityColumns":219,"resourceColumns":255,"pcbaColumns":299},[92,140,169,198],{"heading":93,"links":94},"PCB Product Families",[95,98,101,104,107,110,113,116,119,122,125,128,131,134,137],{"label":96,"path":97},"FR-4 PCB","\u002Fpcb\u002Ffr4-pcb",{"label":99,"path":100},"High-Speed PCB","\u002Fpcb\u002Fhigh-speed-pcb",{"label":102,"path":103},"Multilayer PCB","\u002Fpcb\u002Fmultilayer-pcb",{"label":105,"path":106},"HDI PCB","\u002Fpcb\u002Fhdi-pcb",{"label":108,"path":109},"Flexible PCB","\u002Fpcb\u002Fflex-pcb",{"label":111,"path":112},"Rigid Flex PCB","\u002Fpcb\u002Frigid-flex-pcb",{"label":114,"path":115},"Ceramic PCB","\u002Fpcb\u002Fceramic-pcb",{"label":117,"path":118},"Heavy Copper PCB","\u002Fpcb\u002Fheavy-copper-pcb",{"label":120,"path":121},"High Thermal PCB","\u002Fpcb\u002Fhigh-thermal-pcb",{"label":123,"path":124},"Antenna PCB","\u002Fpcb\u002Fantenna-pcb",{"label":126,"path":127},"High Frequency PCB","\u002Fpcb\u002Fhigh-frequency-pcb",{"label":129,"path":130},"Microwave PCB","\u002Fpcb\u002Fmicrowave-pcb",{"label":132,"path":133},"Metal Core PCB","\u002Fpcb\u002Fmetal-core-pcb",{"label":135,"path":136},"High-Tg PCB","\u002Fpcb\u002Fhigh-tg-pcb",{"label":138,"path":139},"Backplane PCB","\u002Fpcb\u002Fbackplane-pcb",{"sections":141},[142],{"heading":143,"links":144},"RF & Materials",[145,148,151,154,157,160,163,166],{"label":146,"path":147},"Rogers PCB","\u002Fmaterials\u002Frf-rogers",{"label":149,"path":150},"Taconic PCB","\u002Fmaterials\u002Ftaconic-pcb",{"label":152,"path":153},"Teflon PCB","\u002Fmaterials\u002Fteflon-pcb",{"label":155,"path":156},"Arlon PCB","\u002Fmaterials\u002Farlon-pcb",{"label":158,"path":159},"Megtron PCB","\u002Fmaterials\u002Fmegtron-pcb",{"label":161,"path":162},"ISOLA PCB","\u002Fmaterials\u002Fisola-pcb",{"label":164,"path":165},"Spread Glass FR-4","\u002Fmaterials\u002Fspread-glass-fr4",{"label":167,"path":168},"Impedance Control","\u002Fpcb\u002Fpcb-impedance-control",{"sections":170},[171],{"heading":172,"links":173},"Manufacturing \u002F Stackups",[174,177,180,183,186,189,192,195],{"label":175,"path":176},"Quickturn Prototypes","\u002Fpcb\u002Fquick-turn-pcb",{"label":178,"path":179},"NPI & Small Batch (PCB)","\u002Fpcb\u002Fnpi-small-batch-pcb-manufacturing",{"label":181,"path":182},"High-Volume Production","\u002Fpcb\u002Fmass-production-pcb-manufacturing",{"label":184,"path":185},"High Layer Count PCB","\u002Fpcb\u002Fhigh-layer-count-pcb",{"label":187,"path":188},"PCB Fabrication Process","\u002Fpcb\u002Fpcb-fabrication-process",{"label":190,"path":191},"Advanced PCB Manufacturing","\u002Fpcb\u002Fadvanced-pcb-manufacturing",{"label":193,"path":194},"Special PCB Manufacturing","\u002Fpcb\u002Fspecial-pcb-manufacturing",{"label":196,"path":197},"Multi-Layer Laminated Structure","\u002Fpcb\u002Fmultilayer-pcb-lamination-services",{"heading":199,"links":200},"Specialties & Resources",[201,204,207,210,213,216],{"label":202,"path":203},"PCB Design & Layout Services","\u002Fpcba\u002Fpcb-design-services",{"label":205,"path":206},"PCB Surface Finishes","\u002Fpcb\u002Fpcb-surface-finishes",{"label":208,"path":209},"PCB Drilling & Vias","\u002Fpcb\u002Fpcb-drilling",{"label":211,"path":212},"PCB Stackup","\u002Fpcb\u002Fpcb-stack-up",{"label":214,"path":215},"PCB Profiling","\u002Fpcb\u002Fpcb-profiling",{"label":217,"path":218},"Quality & Inspection","\u002Fpcb\u002Fpcb-quality",[220,225,230,235,240,245,250],{"links":221},[222],{"label":223,"path":224},"Rigid PCB Capability","\u002Fcapabilities\u002Frigid-pcb",{"links":226},[227],{"label":228,"path":229},"Rigid-Flex Capability","\u002Fcapabilities\u002Frigid-flex-pcb",{"links":231},[232],{"label":233,"path":234},"Flex PCB Capability","\u002Fcapabilities\u002Fflex-pcb",{"links":236},[237],{"label":238,"path":239},"HDI PCB Capability","\u002Fcapabilities\u002Fhdi-pcb",{"links":241},[242],{"label":243,"path":244},"Metal PCB Capability","\u002Fcapabilities\u002Fmetal-pcb",{"links":246},[247],{"label":248,"path":249},"Ceramic PCB Capability","\u002Fcapabilities\u002Fceramic-pcb",{"links":251},[252],{"label":253,"path":254},"Heavy Copper PCB Capability","\u002Fcapabilities\u002Fheavy-copper-pcb",[256,267,291],{"heading":257,"links":258},"Downloads",[259,262,265],{"label":260,"path":261},"Materials Datasheet \u002F Processing Notes","\u002Fresources\u002Fdownloads-materials",{"label":263,"path":264},"PCB DFM Guidelines","\u002Fresources\u002Fdfm-guidelines",{"label":196,"path":266},"\u002Fpcb\u002Fmulti-layer-laminated-structure",{"heading":268,"links":269},"Tools",[270,273,276,279,282,285,288],{"label":271,"path":272},"Gerber Viewer","\u002Ftools\u002Fgerber-viewer",{"label":274,"path":275},"PCB Viewer","\u002Ftools\u002Fpcb-viewer",{"label":277,"path":278},"BOM Viewer","\u002Ftools\u002Fbom-viewer",{"label":280,"path":281},"3D Viewer","\u002Ftools\u002F3d-viewer",{"label":283,"path":284},"Circuit Simulator","\u002Ftools\u002Fcircuit-simulator",{"label":286,"path":287},"Impedance Calculator","\u002Ftools\u002Fimpedance-calculator",{"label":289,"path":290},"Trace Width Calculator","\u002Ftools\u002Ftrace-width-calculator",{"heading":292,"links":293},"FAQ & Blog",[294,297],{"label":295,"path":296},"FAQ","\u002Fresources\u002Ffaq",{"label":65,"path":298},"\u002Fblog",[300,330,356,389],{"heading":301,"links":302},"Core Services",[303,306,309,312,315,318,321,324,327],{"label":304,"path":305},"Turnkey PCB Assembly","\u002Fpcba\u002Fturnkey-assembly",{"label":307,"path":308},"NPI & Small Batch PCB Assembly","\u002Fpcba\u002Fnpi-assembly",{"label":310,"path":311},"Mass Production PCB Assembly","\u002Fpcba\u002Fmass-production",{"label":313,"path":314},"Flex & Rigid-Flex PCB Assembly","\u002Fpcba\u002Fflex-rigid-flex",{"label":316,"path":317},"SMT & Through-Hole Assembly","\u002Fpcba\u002Fsmt-tht",{"label":319,"path":320},"BGA PCB Assembly","\u002Fpcba\u002Fbga-qfn-fine-pitch",{"label":322,"path":323},"Components & BOM Management","\u002Fpcba\u002Fcomponents-bom",{"label":325,"path":326},"Box Build Assembly","\u002Fpcba\u002Fbox-build-assembly",{"label":328,"path":329},"PCB Assembly Testing & Quality","\u002Fpcba\u002Ftesting-quality",{"heading":331,"links":332},"Supporting Services",[333,335,338,341,344,347,350,353],{"label":334,"path":203},"PCB Design & Layout",{"label":336,"path":337},"Every Support Touchpoint","\u002Fpcba\u002Fsupport-services",{"label":339,"path":340},"Stencil Lab","\u002Fpcba\u002Fpcb-stencil",{"label":342,"path":343},"Components Sourcing","\u002Fpcba\u002Fcomponent-sourcing",{"label":345,"path":346},"IC Programming","\u002Fpcba\u002Fic-programming",{"label":348,"path":349},"Conformal Coating","\u002Fpcba\u002Fpcb-conformal-coating",{"label":351,"path":352},"Selective Soldering","\u002Fpcba\u002Fpcb-selective-soldering",{"label":354,"path":355},"BGA Reballing","\u002Fpcba\u002Fbga-reballing",{"heading":357,"links":358},"Quality & Testing",[359,362,365,368,371,374,377,380,383,386],{"label":360,"path":361},"Quality Inspection","\u002Fpcba\u002Fquality-system",{"label":363,"path":364},"First Article Inspection (FAI)","\u002Fpcba\u002Ffirst-article-inspection",{"label":366,"path":367},"Solder Paste Inspection (SPI)","\u002Fpcba\u002Fspi-inspection",{"label":369,"path":370},"AOI Optical Inspection","\u002Fpcba\u002Faoi-inspection",{"label":372,"path":373},"X-Ray \u002F CT Inspection","\u002Fpcba\u002Fxray-inspection",{"label":375,"path":376},"ICT In-Circuit Testing","\u002Fpcba\u002Fict-test",{"label":378,"path":379},"Flying Probe Testing","\u002Fpcba\u002Fflying-probe-testing",{"label":381,"path":382},"FCT \u002F Functional Testing","\u002Fpcba\u002Ffct-test",{"label":384,"path":385},"Final Inspection & Packing","\u002Fpcba\u002Ffinal-quality-inspection",{"label":387,"path":388},"Incoming Quality Control","\u002Fpcba\u002Fincoming-quality-control",{"heading":390,"linkClass":391,"links":392},"Industry Applications (Entry)","text-nowrap",[393,396,399,402,405,408,411,414,417,420,423],{"label":394,"path":395},"Server \u002F Data Center","\u002Findustries\u002Fserver-data-center-pcb",{"label":397,"path":398},"Automotive \u002F EV","\u002Findustries\u002Fautomotive-electronics-pcb",{"label":400,"path":401},"Medical","\u002Findustries\u002Fmedical-pcb",{"label":403,"path":404},"Telecom \u002F 5G","\u002Findustries\u002Fcommunication-equipment-pcb",{"label":406,"path":407},"Aerospace & Defense","\u002Findustries\u002Faerospace-defense-pcb",{"label":409,"path":410},"Drone \u002F UAV","\u002Findustries\u002Fdrone-uav-pcb",{"label":412,"path":413},"Industrial Control & Automation","\u002Findustries\u002Findustrial-control-pcb",{"label":415,"path":416},"Power & New Energy","\u002Findustries\u002Fpower-energy-pcb",{"label":418,"path":419},"Robotics & Automation","\u002Findustries\u002Frobotics-pcb",{"label":421,"path":422},"Security \u002F Security Equipment","\u002Findustries\u002Fsecurity-equipment-pcb",{"label":424,"path":425},"PCB Industry Overview →","\u002Fpcb-industry-solutions",1794926068934]