Store and handle solder paste according to the current instructions for the exact product, and keep enough history to connect each container to the boards printed with it. Shipping exposure, unopened storage, conditioning, an opened container and paste on a stencil are different conditions; a limit for one does not automatically apply to the others.
Choosing the material comes first: see solder paste selection. Once a product has been chosen, the task is to preserve its identity and handling history through each shift. Solder paste inspection evaluates printed deposits; it does not reconstruct an unknown storage history.
Which time limit applies to the paste?
Read the label and the current technical data sheet (TDS) together with the supplier's applicable handling instructions. Confirm the product, alloy, powder designation, package and lot. Use the manufacturer's stated conditions and the site's approved procedure, including any customer requirements.
| Stage | What to establish | Common mistake to avoid |
|---|---|---|
| Transit and receipt | Delivery time, package condition, available temperature evidence and the supplier's transit guidance. Record exceptions. | Treating a long-term storage limit as a shipping limit, or assuming a warm package proves damage. |
| Unopened storage | Required conditions, lot identity and manufacturer expiry or use-by date. Keep the actual storage record. | Applying a shelf life quoted for another product or temperature. |
| Conditioning before opening | Time removed from storage, how the sealed container reached the specified working condition, and any temperature verification required by the procedure. | Assuming the same warm-up time suits every container. Opening a cold container in a warmer room can lead to condensation. |
| Open container | Opening date and time, subsequent conditions, handling and any product-specific open-container limit. | Treating a stencil-life figure as the allowed life of the whole opened jar. |
| On the stencil | Time paste was applied, additions, interruptions, removal, environmental conditions and the applicable working-life rule. | Restarting the clock merely because fresh paste was added, unless the approved procedure explicitly supports that treatment. |
| Return or reuse | Whether the product and site procedure allow it, how material is identified and segregated, and the recorded disposition. | Mixing used and unused paste or returning paste to stock without an approved rule. |
These clocks can overlap. For example, time on the stencil is part of the used paste's history, but it does not necessarily describe the exposure of all paste remaining in the container or follow the same limit. Do not infer a new expiry from one clock without the supplier's instructions and the site procedure.
A product-specific example
Indium's Indium8.9HF Pb-Free data sheet, R27, lists separate shelf-life conditions for unopened containers and an up to 60-hour stencil life under its stated 22–28 °C and 30–60% relative-humidity conditions. The stencil figure is not an opened-jar life or a rule for other products. The same sheet calls for equilibration before use, notes that container size affects the time required, and says to verify paste temperature before use. A preparation interval alone does not prove that every container has reached working temperature.
Manufacturer advice can differ. AIM's handling guidance and Indium's handling guidance both direct users to product-specific information. Verify the current revision for the material in hand, especially for storage, freezing, conditioning, reuse and expiry. Do not apply this example's numbers to another paste.
What if a shift cannot account for part of the container history?
Consider a hypothetical jar with container ID J03 from lot L17, assigned to build B24. The times below illustrate a missing record; they are not operating limits.
| Event | Record available |
|---|---|
| Monday 08:00 | Sealed jar J03, lot L17, taken from controlled storage; removal logged. |
| Monday 11:00 | Operator logs opening and application to printer P2 for build B24. |
| Monday 14:00 | Printing stops; the last confirmed panel ID and the paste remaining are recorded. |
| Tuesday 08:00 | A jar marked J03 and L17 is found near P2. Its location, temperature and seal status between shifts are not documented; a new operator has not used it. |
The missing interval is an exposure question, not proof that the paste has failed or remains usable. Identify and hold the jar and any paste possibly returned from the stencil. Hold any printed panels whose connection to the uncertain interval cannot yet be ruled out, according to the site's containment procedure. Preserve the labels and records; avoid mixing, reworking or discarding material before the responsible quality or process owner has documented the disposition.
Reconcile the jar identifier, printer and panel sequence with shift notes, access and storage logs, stencil additions, inspection records and operator accounts. Establish the last confirmed acceptable event and, if recorded, the first confirmed use of a different, traceable container. Where the boundary remains uncertain, document the affected range rather than guessing. A panel printed before the gap is not automatically affected by later exposure, but its identity must be established from the records.
The authorized process or quality owner compares the known facts with the exact product's current instructions and customer requirements, consults the paste supplier where needed, and records the decision for both material and affected product. A test print or a satisfactory deposit measurement can inform the investigation; neither alone reconstructs the missing history or proves final solder-joint reliability. If no defensible disposition is available, maintain the hold and escalate under the applicable procedure.
What should operators record at each handoff?
A container record can be paper or electronic, provided it is legible, retained and linked to the production record. Capture:
- Product designation and data-sheet revision, alloy and powder designation, package, lot, manufacturer expiry and a unique container ID.
- Receipt date, shipment exception and available temperature evidence; storage location and temperature history or excursion record.
- Removal from storage, conditioning and opening times; actual paste temperature when required by the approved procedure.
- Printer and stencil identification, application and removal times, additions, interruptions, ambient conditions where required, and container or stencil disposition.
- Build, panel or serial range, shift and operator, exceptions, decision owner, supporting evidence and final disposition.
Use the site's approved handling instructions for mixing and dispensing; a jar, cartridge and syringe may have different requirements. Keep suspect or returned material identifiable and separate from fresh stock until its disposition is authorized.
What do print defects tell you about paste condition?
Changes in deposit volume, incomplete release, slumping, dried paste or separation are reasons to investigate, not a diagnosis of a single cause. Review the paste history alongside stencil apertures and cleaning, printer setup, board support and alignment, environment and inspection results. Record observations before changing several variables at once. The supplier's product guidance and the assembler's controlled process define which checks and corrective actions are appropriate.
For a new build, ask the assembler how paste identity is tied to panels, how storage and stencil exposure are monitored, who can approve an exception, and what evidence will accompany an affected lot. Supply the selected paste requirements, assembly documentation, inspection and traceability expectations, and any customer-imposed restrictions. The paste supplier advises on its material; the assembler controls and documents its process; the product owner remains responsible for qualification of the finished assembly.
APTPCB offers PCB fabrication and turnkey PCB assembly. For a PCB assembly quote, provide the assembly files and any paste, inspection and traceability requirements; confirm the material and records included in the project scope.
Frequently asked questions
Can solder paste be used after the date on the label?
Do not assume either acceptance or automatic rejection from a generic rule. Follow the applicable product instructions and site and customer requirements; an authorized owner should consult the supplier and document any permitted assessment and disposition before use.
Does passing solder paste inspection prove that storage was acceptable?
No. Inspection describes the measured deposits under its inspection conditions. It cannot recover a missing storage record or establish all material properties and long-term assembly performance.
Can paste left on the stencil go back into the original jar?
Follow the specific supplier's instructions and the site's approved reuse procedure. AIM advises against combining used and unused paste in the same container; consult the applicable supplier guidance for other products.
Technical references
- Indium Corporation, Indium8.9HF Pb-Free Solder Paste product data sheet, R27. The storage and stencil-life values are specific to this product and the stated conditions; verify the current revision before use.
- Indium Corporation, Solder Paste Storage and Handling Guidelines, R5. Consult the selected product's instructions for its specific handling requirements.
- AIM Solder, Solder Paste Storage & Handling Guidelines, NF1. Its guidance refers users to the applicable product data sheet and describes its recommendations for new and used paste.