Moisture-Sensitive Components: MSL Floor Life and Assembly Handoff

Moisture-Sensitive Components: MSL Floor Life and Assembly Handoff
On this page

A moisture sensitivity level (MSL) helps an assembly team manage exposure of a particular component package through its final relevant reflow. The applicable requirements determine how storage and multiple passes are counted. The team needs the actual part and package label, a traceable exposure record, the applicable handling procedure and a plan for exceptions. A sealed bag or a successful electrical test alone does not tell the assembler how much floor life remains.

This guide is for the person preparing a kit, accepting components or planning assembly. It addresses moisture-sensitive surface-mount devices; bare PCB storage and disposition addresses unassembled boards. The turnkey component substitution guide covers a broader incoming-material and approval workflow; the question here is how to keep a specific lot's exposure history usable at the assembly line.

Why an exposure record matters

Some non-hermetic packages absorb moisture from the surrounding air. During rapid heating, that moisture can contribute to internal delamination, cracking or other damage. A visible bulge may indicate a problem, but the absence of visible damage or a passing electrical test does not establish that internal damage is absent. Moisture is one possible mechanism among several; an actual failure needs investigation.

The relevant rating belongs to a particular component and package under stated classification conditions. Two parts with a similar outline do not necessarily share the same MSL, floor-life conditions or allowable thermal history. Record the manufacturer's part number and package along with the lot; do not substitute a rating from a visually similar device.

IPC/JEDEC J-STD-020 addresses moisture and reflow sensitivity classification. J-STD-033 addresses handling, packing, shipping and use. The applicable edition, the component maker's instructions and the agreed assembly procedure determine how a particular lot is handled. Confirm any conflict or missing information before using the parts.

Separate four things that are easy to confuse

Item What it addresses What to check
Sealed-package shelf life Time and storage conditions applicable while a device remains in its specified unopened packaging The actual label, seal date, supplier instructions and storage history; limits are not universal.
Floor life Exposure allowed for the device under the conditions stated by its applicable requirements before relevant reflow The specific part and package, recorded intervals, environmental conditions and approved handling procedure.
Classification reflow profile Conditions used to establish a device's moisture/reflow classification Package classification temperature and manufacturer restrictions. It is not an oven recipe for every board.
Assembly reflow profile The thermal exposure the assembled board and its components actually experience The assembler's validated process, solder paste, board and components, plus any further reflow or rework.

Shelf life is not a substitute for floor-life tracking. An opened bag with a seal date inside a supplier's stated shelf life can still have an incomplete exposure record. Nor does a component's classification automatically prove that the actual board profile, number of passes or rework conditions are acceptable.

At receiving: identify the lot before opening the bag

For each moisture-sensitive lot, match the manufacturer part number, package, quantity and lot identification against the approved order or kit record. Preserve the original label and applicable supplier documentation. Record the MSL, handling conditions and relevant reflow restrictions from the label and applicable component instructions, along with any available packing or seal date. Resolve missing information before use.

Inspect the external package and its seal. A punctured bag, missing identification, apparently opened bag or disagreement between labels should trigger the agreed hold-and-notify process. Do not open an intact bag solely to read the humidity indicator unless the receiving procedure calls for it: opening can start or add exposure that must be managed.

When the package is opened, inspect the humidity indicator and desiccant as required by the component supplier and applicable procedure. Record the result and opening time. A card indicates conditions according to its own use instructions; its color alone should not be treated as a universal acceptance rule. The presence of desiccant by itself also does not establish that the devices are fit for assembly.

Incoming condition Immediate action Information to obtain before release
Sealed, identifiable bag Keep under specified conditions until needed; retain the label and receipt record. Applicable shelf-life and storage requirements.
Previously opened partial reel with complete records Link the part and lot to the recorded exposures and storage intervals. Whether the procedure accepts those records and how to calculate remaining exposure.
Unknown opening time or damaged seal Place the affected material on hold; tell the owner or supplier. Disposition from the responsible quality authority and component maker where needed.
Missing MSL or mismatched identification Segregate the lot rather than borrow a rating from a similar part. Confirmed part, package, label and handling instructions.

For customer-supplied components, agree who owns that disposition and whether the assembler may perform corrective processing. See turnkey vs. consigned assembly for the wider division of sourcing and material responsibility.

Work out the remaining exposure from the record

The following example is a hypothetical accounting exercise, not an allowance for a real device. Assume a specific component's applicable label and procedure permit 168 hours under compliant environmental conditions, not specified here. Assume both recorded intervals count in full under that procedure, with no unrecorded exposure. Dry storage between them is acceptable only under the conditions and rules in the approved procedure.

Recorded step Exposure to count
First eligible interval after opening 48 hours
Second eligible interval after approved storage 36 hours
Total counted exposure 48 + 36 = 84 hours
Nominal remaining allowance 168 - 84 = 84 hours

The result is useful only if the label, conditions, time records and treatment of storage all apply to this lot. A temperature or humidity excursion, missing interval, uncertain storage condition or different label leaves this simple calculation unverified until assessed against the applicable requirements. Hold the lot for a documented disposition instead of guessing how many hours remain. The actual process must account for the time through the final relevant reflow, including intervals between assembly passes when applicable.

Mark partial reels, trays and split lots so the remaining quantity stays linked to its own record. A transfer between sites or suppliers needs the same information, not just a statement that the parts were "stored dry."

Repackaging, drying and rework need separate decisions

Resealing a bag is a packaging action. It does not, by itself, establish a new full floor-life allowance. An approved dry-storage or drying process may change how exposure is accounted for, but the conditions, duration and record treatment must follow the applicable requirements and component instructions. Keep the previous exposure history and the action taken with the lot.

If exposure is exceeded or uncertain, the responsible team should determine whether the components can be dried or need another disposition. Do not apply a generic bake temperature and duration: package construction, prior exposure, carrier material and supplier instructions matter. A reel, tape, tray or tube suitable for normal handling may not tolerate the proposed process. Moving devices to another carrier also creates identification, traceability and handling risks. Record any authorized processing and its release decision.

Double-sided assembly and later rework add another handoff. A device already mounted on the first side may be exposed again before a later thermal cycle. Other components, board materials and finishes also constrain a rework or drying decision. Agree on the planned passes, elapsed time, storage and any rework requirements before assembly; do not assume a bare-board process is interchangeable with a populated-board process. The reflow profile basics guide explains the broader oven-profile discussion.

What should a kit or assembly handoff contain?

Send the assembler a lot-specific record that can be checked against the physical material:

  1. Manufacturer part number, package, quantity and lot or traceability identifier.
  2. MSL, relevant conditions and component-maker handling and reflow restrictions, with their sources.
  3. Seal date and packaging status where available, plus any receiving discrepancy.
  4. Opening times, eligible exposure intervals, environmental conditions and approved storage intervals.
  5. Remaining allowance or a clear "unknown / on hold" status, with the calculation and assumptions.
  6. Any authorized drying, repackaging, split-lot transfer or other disposition, with dates and traceable records.
  7. Intended assembly passes, rework expectations and the contact authorized to resolve discrepancies.

Agree on what happens when the delivered quantity differs from the record, the label is unreadable or the line cannot complete the planned pass within the remaining allowance. The team should know who can authorize a disposition and whether replacements are available before the job is released. Resolving these questions early can prevent a line stop without treating missing evidence as an acceptance.

APTPCB offers PCB fabrication and turnkey PCB assembly. For a project quote, supply the assembly BOM, identify consigned and partially used lots, and flag parts with short or uncertain remaining exposure. Ask what handling and documentation can be provided for the job. Request project-specific support through the quote page or contact the team.

Frequently asked questions

Does an intact sealed bag prove that the components are ready to use?

No. Check identification, applicable storage and shelf-life conditions, labels and the required receiving evidence. A sealed bag cannot by itself establish that all preceding storage conditions were met.

Does resealing a partial reel reset its floor life?

Do not assume so. Record the exposure and use the approved storage or drying procedure and the device manufacturer's instructions to determine the status after repackaging.

Can visual inspection or a functional test replace the exposure record?

No. Those checks can provide useful evidence but do not reconstruct exposure history or rule out internal damage. Follow the agreed disposition procedure when records are missing or exposure is uncertain.

Is the component's classification temperature the correct oven setting?

No. The classification profile is used to classify a device's moisture and reflow sensitivity. The assembly profile must be established for the actual board, components, paste and process without exceeding applicable device limits.

Technical references