An SMT reel splice joins two component carrier tapes so that a feeder can continue presenting parts. Before the change, verify the incoming reel against the approved build and the feeder's controlled process; after it, keep the outgoing and incoming reel identities connected to the production record. A sound-looking joint does not prove that the right component was loaded or identify the boards that received each lot.
The pick-and-place process covers feeder loading in the wider assembly flow. PCB traceability and lot control addresses the record scope a buyer and supplier agree on. The additional question at a splice is how a reel change becomes a usable production record when the lot boundary is not obvious.
What must be checked before a reel splice?
Start with the released BOM and the machine setup, then check the two reels and the joining method against the site's approved instructions.
| Check | Evidence to confirm | If the evidence is missing |
|---|---|---|
| Part identity | Approved manufacturer and exact part number, reel label, build revision and feeder assignment | Hold the incoming reel for verification. A similar marking or package is not approval for a substitute. |
| Lot and handling status | Reel identifiers, lot codes and any required handling history for both reels | Keep the material identifiable and ask the responsible owner to resolve the gap. |
| Feeder and splice method | Actual feeder and carrier tape, approved joining material, tools and work instruction | Confirm compatibility with the equipment and material documentation before use. |
| Connection and feed | Inspection and verification required by the approved process, including detection where applicable | Follow the site's response for a failed or uncertain check; do not rely on appearance alone. |
| Production linkage | Job, board revision, machine, feeder position and the required reel-to-board records | Record the uncertainty and involve the process or quality owner. |
A reel can contain the same approved part number as another reel while carrying a different manufacturing lot. Joining their tapes does not combine their identities into one lot. Use the site's controlled procedures for equipment safety, ESD handling and moisture-sensitive components. Whether a reel may be spliced while equipment is operating depends on the machine and the site's authorized process.
How do you check the physical splice?
Carrier tape, cover tape, feeder design and joining materials vary. Use the method approved for the actual combination and check the joining-material and equipment instructions before starting. The operator should be able to identify the following in the completed joint:
- Transport-hole alignment: The feeder must be able to advance the joined tapes at the intended pitch. Misalignment can disrupt the feed.
- Carrier and cover tape: Check that the joint does not obstruct the feeder or interfere with the cover tape's intended path. Inspect for damage or loose material that could affect feeding.
- Joint position and detection: Check the joint as required for the feeder and any splice-detection system used on the line. A physical detector and a lot-traceability record serve different purposes.
- Feed verification: Follow the approved inspection and feed-check procedure. Record a failure or uncertain result and follow the site's response before continuing.
If feeding fails at the joint, identify the feeder position and affected material, preserve the reel and event information, and check hole alignment, tape condition, joining material and feeder compatibility. Use the machine's fault response and recheck the joint after any approved correction. Do not assume a successful visual inspection identifies the components or establishes their lot history.
What should a splice event record contain?
Use a paper or electronic record that can be linked to the actual job and retained under the agreed quality requirements. The needed level of detail depends on whether the program tracks material to a build lot, panel, individual board or another defined level.
- Work order, board and BOM revision, machine, feeder identification and slot.
- Approved manufacturer and part number; outgoing and incoming reel identifiers and component lot codes.
- Relevant material status and any handling exception, with disposition where required.
- Date and time of the event, operator, approved joining method and material, and verification result.
- Available machine or production event identifiers, board or panel sequence, and the evidence used to determine the transition range.
- Any unresolved gap, the person responsible for its disposition and the final decision.
Do not write a precise first board for the new lot simply because the incoming reel was scanned at a particular time. The event at the splice and the point at which a part reaches a board may be recorded differently by different systems. Confirm the equipment's actual behavior, any buffering and the time relationship between records for the installation in use.
How do you investigate an uncertain lot transition?
In this hypothetical example, an assembler is building revision R3 under work order W42. Feeder F7 supplies reference designator U12. Reel A and reel B both carry the approved part number, but their lot codes are LA and LB.
| Event | Evidence in this example |
|---|---|
| Before change | The released setup identifies reel A, lot LA, on F7. Placement records, whose association has been checked for this example, link LA at U12 to panels P100 through P109. |
| Reel change | Reel B, lot LB, is scanned and joined to reel A at 10:15. The record identifies F7 and the operator, but does not establish the board on which LB first appears. |
| After change | A separately verified placement record links LB at U12 to panels P130 through P139. The records for P110 through P129 do not establish which lot supplied U12. Machine buffering and the event-to-placement timing are unknown. |
| Later notice | The supplier reports that lot LB requires investigation. The process owner must identify the potentially affected product. |
The 10:15 scan alone cannot split the panels into LA and LB. In this example, P130 through P139 are known to include LB at U12; P110 through P129 could contain it. P110 through P139 are an initial identified review population, not necessarily the complete population. Check later panels in W42, if any, and all other possible uses of LB, subject to the site's containment procedure. P100 through P109 have verified LA records for U12 in this example, but the owner still needs to check whether LB could have entered those panels through another relevant feeder, reference designator or event before excluding them.
Preserve the reel labels, event and placement logs, machine configuration, panel sequence, inspection status and shift records. Reconcile the complete use history and ask the equipment or software provider how the specific system records a splice, pending picks and board association. If records cannot narrow the range, document the uncertainty rather than inferring a boundary from the scan. The authorized quality owner determines the actual hold, release and customer notification under applicable agreements and procedures.
Does a splice detector provide lot traceability?
Not by itself. A compatible detection feature may identify a joining point, but detecting a physical transition is different from linking each component lot to a specific board. What the machine records depends on its equipment, software and configuration.
Ask the equipment supplier and assembler what their particular configuration captures: reel and lot identification, event time, board or placement association, exceptions, and whether the records can be retrieved for the required period. Demonstrate the requested linkage on a representative build before relying on it for containment.
What should a buyer request before assembly?
Provide the released BOM and approved alternates, identify components requiring lot linkage, and define whether traceability must reach the build lot, panel or individual board. State record retention, retrieval, change-notification and customer approval requirements in the order or quality agreement.
Ask the assembler how it verifies reels at replenishment, records a lot transition, handles an unreadable label or missing event, and determines a possible affected range. Request an example of the records available for the agreed scope, with sensitive information removed where necessary. APTPCB offers turnkey PCB assembly; use the quote page to share your BOM and traceability requirements, and confirm the records available for your project.
Frequently asked questions
Can different component lots be joined on one feeder?
That depends on the released build, customer requirements and the assembler's approved material-control process. If permitted, preserve the identity and applicable handling history of each lot and the agreed link to production records.
Does a successful feed check prove that the correct component was installed?
No. A feed check addresses the checks performed on feeding; it does not independently prove part identity or lot history. Verify the incoming material and feeder assignment against the released build.
What happens when the first board using the new reel is unknown?
Document the gap, preserve the available evidence and follow the site's containment procedure. The responsible owner evaluates the potentially affected range using verified records and the applicable customer requirements.
Source
allSMT, Joining SMD carrier tapes: guidance on preparation, tape alignment, inspection and feed-failure records. Check the instructions for the actual feeder and joining materials used on the line.