SMT Stencil Underwipe: How to Investigate Print Alerts Before Changing the Cleaning Cycle

SMT Stencil Underwipe: How to Investigate Print Alerts Before Changing the Cleaning Cycle
On this page

When solder paste inspection flags a deposit and an operator also sees residue under the stencil, hold the affected work for review and preserve both observations. Neither observation alone proves the wipe cycle caused the alert. The useful decision is whether the current printing process remains suitable for this board, paste, stencil and printer, and what evidence is needed before changing it.

Under-stencil wiping removes material from the underside of a stencil during printing. Its result depends on the equipment, wipe material, any cleaning agent, paste and stencil. A clean-looking stencil alone does not verify the printed deposits. Use the solder paste inspection guide for the broader inspection and disposition workflow.

What should happen when two observations occur together?

Consider this hypothetical example:

Event Observation Immediate decision
Start of the run Panel A passes the project's configured print inspection. Its board revision, stencil, paste lot and printer recipe are recorded. Keep A's inspection record as a traceability reference; a pass does not prove later panels are good.
Later in the run SPI flags a low-volume deposit on panel B. The operator also observes a smear on the stencil underside. The smear is an observation made separately from SPI. Identify and hold panel B and the potentially affected interval under the site's containment procedure. Preserve the SPI image, measurement, alarm settings and stencil observation.
Initial review The team checks which panels ran after the last relevant verified result, including panels without usable inspection data and any already moved downstream. Extend containment or recovery as required by the project procedure. Do not release on the assumption that wiping alone corrected the issue.

The process and quality owners then establish the actual interval and disposition. A panel ID, time and last accepted result are starting points, not proof that every intervening panel was inspected or that the alarm was valid. Record gaps in coverage and locate any affected material that has left the printing station.

What evidence distinguishes a wipe issue from another cause?

Capture the production state before adjusting it. Different observations can have more than one explanation, and several conditions may be present at once.

Evidence What to record What it can and cannot tell you
SPI alert Panel and pad identifiers, original image, measured value, configured limits, inspection program and any missed or false calls. A measurement at an inspected location. It does not by itself identify why the deposit changed or the condition of uninspected locations.
Underside and apertures Photos or a documented observation, location relative to the affected pads, before any approved cleaning. Residue or damage may be visible. A smear alone does not prove transfer to a particular panel or establish a root cause.
Process history Printer and recipe revision, count since the last wipe, wipe sequence and consumables, interruptions, board support and alignment records. Establishes what was recorded during the interval. It does not establish settings that were not logged or rule out other variables.
Materials and tooling Paste product, lot and use history; stencil identity, revision, condition and coating if present; wipe media and cleaner identity. Makes a comparison reproducible and identifies changes to investigate with suppliers.
Affected product Panel IDs, inspection coverage, location, reprint or reinspection history and prior dispositions. Defines what can be located and reviewed. Missing records remain open questions, not automatic passes.

Check the measurement and program first: an incorrectly taught pad, an alignment problem or a changed inspection setup can affect an alert. Also investigate board support, stencil condition and fit, paste condition and other print settings as applicable. Review the solder paste storage and handling record where paste history is relevant. A result that improves after cleaning is useful evidence for further investigation, but does not isolate which changed condition caused the improvement.

What does a wipe cycle actually control?

A printer may use dry wiping, a compatible cleaning agent, vacuum assistance or a combination specified by its process. The appropriate arrangement and interval depend on the actual equipment and materials. Follow the printer, stencil, paste and cleaning-agent suppliers' instructions, applicable safety data sheets and site safety controls, and verify compatibility before making changes.

Under-wiping during a run is distinct from cleaning a removed stencil at changeover or dealing with a misprinted board. Each has different tooling, handling and contamination concerns. Neither a visually clean stencil nor a single acceptable print demonstrates that a changed process will remain stable throughout a run.

How can a team compare a proposed change?

After containment, the process owner can plan a controlled comparison under the site's approved procedures.

  1. Define the question and the decision. For example: does the proposed wipe recipe maintain the agreed deposit inspection results for this particular combination? Decide in advance who may authorize the trial, accept the evidence and release product.
  2. Fix and record the conditions. Identify the board and stencil revisions, relevant apertures, paste product and lot, printer, wipe media, cleaner, program and environmental conditions. Record any differences or interruptions; follow supplier instructions for material handling and machine operation.
  3. Compare one planned change. Use the approved reference recipe and proposed recipe with comparable material and observation conditions. Record the actual sequence and print history, including stops, wipe events and any unavoidable changes. Do not assume a setting is transferable to a different product or line.
  4. Review observations and coverage. Examine the specified deposits and any separately defined areas between them where the inspection system can assess them. Record measurement setup, traceability and gaps, as well as stencil condition and results across the agreed trial period. An SPI result is evidence about the printed paste; it is not a substitute for every later assembly or product test.
  5. Document disposition and ownership. If the evidence is incomplete or the agreed criteria are not met, keep the change unapproved and follow the containment plan. If accepted, record the authorized recipe and scope, affected material disposition, reinspection or reprint records where applicable, and the conditions that would require another review.

The project must define inspection criteria and sampling before the trial. An interval or alert threshold taken from a different board or a laboratory article does not establish an acceptance limit for this one. The stencil design tutorial covers the separate decisions about apertures, stencil construction and print design.

What can published tests tell you?

An AIM Solder application-lab study compared two under-stencil cleaners with a particular SAC305 no-clean paste and test vehicle. Its test used an eight-hour run without replenishing paste, a 100 µm stencil, and a wet-vacuum-dry wipe after every five printed boards. The authors reported differences in monitored deposit measurements, including per-board averages, under those conditions. That setup is not a recommended interval or proof of finished assembly yield or field reliability.

An Indium and KYZEN paper, first published in 2013, describes two investigations of stencil surfaces and cleaning. In one test, cleaner was applied manually because automatic solvent wiping was unavailable, followed by a dry-vacuum-dry cycle. The observations were specific to the tested materials and methods; they do not rank cleaners for every paste or printer. Both papers illustrate why a proposed recipe should be checked with the actual materials and process, not adopted from a headline result.

What should an assembly handoff include?

Provide the board and stencil design revisions, manufacturing files, BOM and any specified paste or cleanliness requirements. Identify critical deposit locations and the inspection or reporting requirements agreed for the project. If an alert or prior issue prompted the request, include its panel IDs, images, measurements, inspection settings, material and process history, and any open containment decisions.

Ask the assembler what inspection coverage and records it can provide, who approves a process change, how affected panels are traced and dispositioned, and how proposed materials and equipment settings are reviewed. Agree on project-specific acceptance criteria and deliverables before production. APTPCB offers PCB fabrication and turnkey PCB assembly. Use the quote page to share the relevant files and open questions; confirm the agreed inspection and records for the project. The assembler's process review and the product owner's qualification remain separate responsibilities.

Frequently asked questions

Does a smear under the stencil prove the wipe interval is too long?

No. It is a reason to preserve evidence and investigate the wipe, printing conditions and relevant inspection results. It does not establish a single cause or the disposition of a panel.

Can the team use the same wipe interval for every board?

An interval is a process setting for a particular combination of board, stencil, materials and equipment. Establish and review it under the applicable process controls rather than assuming it transfers unchanged.

Does a clean SPI result prove the finished assembly is acceptable?

No. SPI provides information about inspected paste deposits under its configured measurement and coverage. Finished solder joints and product qualification may require additional inspection or tests defined by the project.

Technical references